Aeon labs z stick gen5 soft reset install#
Aeon labs z stick gen5 soft reset full#
Aeon labs z stick gen5 soft reset software#

If you had 100 or so, might be a different story. I only have about 22 zwave devices though. However, if it was me, I would just exclude and reinclude everything at that point. Restoring the nvm to the new zstick, if itвЂ™s the identical model and firmware, вЂњshouldвЂќ restore the zwave network without reincluding everything. My thoughts on NVM though- if something goes wrong with it, your zwave stick is likely shot, and youвЂ™ll need a new one anyway. It will not include the NVM data, as that resides on the zstick itself. HA or Z-Stick failure)ДЄ HA general backup will backup the addon data, which should include the nodes.json and settings.json data. Is HA general backup combined with backing up nodes.js and controller NVM within ZWave JS to MQTT sufficient to recover in the event of catastrophic failure (e.g. I want to minimise the impact of / improve speed to recover from any failure.

Is there a way to have a second Z-stick kept in sync, other than manually restoring NVM, to keep a backup ZWave network available?.

Is there a way to automate the Z-Wave backups, or is it just a case for now of вЂњRemember to do it when you change anything in ZWaveвЂќ?.

Is HA general backup combined with backing up nodes.js and controller NVM within ZWave JS to MQTT sufficient to recover in the event of catastrophic failure (e.g.

IвЂ™m assuming that neither of those (ZWave nodes details or NVM) are captured in my General HA backup routine, and that I need to be backing them up separately. I can see in ZWave JS to MQTT control panel that I can backup nodes.js, and it now also allows to backup the controller NVM.

Aeon labs z stick gen5 soft reset full#

I backup HA daily to Google Drive using GitHub - sabeechen/hassio-google-drive-backup: Automatically create and sync Home Assistant backups into Google Drive, and do a monthly full snapshot of the HA VM backed up to AWS. It should not show up again while scanning.There are some older topics here on backups, but as a new Z-Stick user there are some changes and I have some follow-on questions. Remove the device from OH Inbox if needed.In the вЂњDevice ManagementвЂќ Section it should state Device # вЂњIDвЂќ as excluded.Now you should be able to select the Node ID at the top of the вЂњNetwork MaintenanceвЂќ Section and click on вЂњRemove failed NodeвЂќ.Choose again your dead nod and click again on вЂњMark Battery Device as failedвЂќ.wait 30 sec as stated until the job is done.In the Network Maintenance Section s elect your device Node ID and click вЂњ Mark Battery Device as failedвЂќ.Hover on вЂњNetworkвЂќ and klick on вЂњControlвЂќ.Go into ExpertGui Mode and follow the folloing steps:.

Aeon labs z stick gen5 soft reset install#

Start zway-service (go to install locateion and type вЂњ./z-way-serverвЂќ).

But I recommend to at least remove the thing)

(In OH set device as failed and remove it, maybe this step is not needed.

Install zway server (something like -dpkg -x z-way-3.2.0_b вЂњfolder-locationвЂќвЂ“.

To make it clear for everyone who is struggling, here is the detailed procedure: I finally managed to remove the devices using z-way-server (on RPi 3+, openhabian and raZberry/ controller.

IвЂ™m running openHAB2 v2.5 on a Raspberry Pi 4. So is there working solution or work around for this problem? Then I deleted the xml files which where generated during inclusion of the вЂњghostвЂќ nodes from the /Zwave folder.Д«ut every time IвЂ™m searching for new ZWave things the вЂњghostвЂќ nodes I thought that were deleted appear again.

Enabled вЂњRemove device from controllerвЂќ.

Set the вЂњghostвЂќ node into editing mode again.

I tried the binding to delete it from the ZWave USB stick byДЄs I read in certain threads the ZWave USB stick will only remove failed I hoped that this marked the вЂњghostвЂќ node as failed in the ZWave USB stickвЂ™s internal database. And starting the exclusion to my mind will delete the door lock instead of the ghost knodes.

Aeon labs z stick gen5 soft reset software#

The software asks me to initialize the exclusion procedure by pressing the button - which is impossible because I included the door lock successfully. These ghost nodes were generated BEFORE successful inclusion of the door lock.Д«ecause IвЂ™m running a linux system, I tried to use the ZWave tools вЂњZenSysвЂќ and вЂњHS3вЂќ in a virtual machine and tried to delete the ghost nodes. After I added the вЂњABUS Z-Wave HomeTec CFA3010вЂќ door lock to the Z-Wave database - thanks to Chris, Bruce and suhui - I have to remove two вЂњghostвЂќ nodes (nodes 10 and 11) from my Aeotec Z-Wave USB stick.

Aeon labs z-stick gen5 soft reset